Jiffy Mixers

Product Instructions-

1. Tighten power tool chuck onto drive shaft of mixer.

2. The mixer MUST BE FULLY IMMERSED in the material to be mixed before turning on the power tool, and MUST BE KEPT FULLY IMMERSED WHILE IN MOTION.

3. Hold power tool and mixer firmly. The container in which mixing is to be done should be secure so that it will not be thrown, spilling contents.

4. PREPARED, PACKAGED STOCK -TYPE materials, such as powders or pigments used in formulation can produce a sticky mass on the bottom of the container which must be loosened and dispersed. SUBMERGE mixer to within approximately 1″ of bottom of container. Turn power on and move mixer around bottom area until settled material has been brought into the mixture. Slowly move the mixer up and down and around in the material until contents are thoroughly mixed into a smooth, uniform body.

5. CLEAN mixer after each use. Simply immerse in compatible solvent or water and run until clean. When cleaning solution is flammable, be sure to remove mixer from the power tool. Food service operators can put smaller mixers in their dishwashers.

6. NEVER RUN MIXER OUTSIDE OF THE MIXING OR CLEANING CONTAINER

DO NOT EXCEED RPMS FOR MODELS AS LISTED

LM – Up to 1200 RPMS

HS-1 – Up to 1200 RPMS

HS-2 — Up to 1200 RPMS

HS-3 – Up to 800 RPMS

ES – Up to 1000 RPMS

PS-2 – Up to 450 RPMS

HD – Up to 250 RPMS

Made of 304 polished stainless steel, the LM model is designed for smaller jobs in pint sized containers. It easily fits any 1/4″ electric chucked power tool. The LM model  is designed for a max speed of 1200 RPMS.  Tools with 450-750 RPMS. get the best rate of thorough mixing.  Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the HS-1 model is designed for medium jobs in 1-2 gal. (4-8 qt.) containers. It easily fits any 1/4″ electric chucked power tool.  The HS-1 model is designed for a max speed of 1200 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.  Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the HS-2 model is designed for medium jobs in 1-2 gal. (4-8 qt.) containers. It easily fits any 1/4″ electric chucked power tool.  The HS-2 model is designed for a max speed of 1200 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.  Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the HS-3 model is designed for medium jobs in 1-2 gal. (4-8 qt.) containers. It easily fits any 1/4″ electric chucked power tool.  The HS-3 model is designed for a max speed of 800 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.  Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the ES model is designed for medium to heavy jobs in 2-5 gal. (8-20 qt.) containers. It easily fits any 3/8″ electric chucked power tool.  The ES model is designed for a max speed of 1000 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.  Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the PS-2 model is designed for heavy duty jobs in 10-50 gal. (40-200 qt.) containers. It easily fits any 1/2″ electric chucked power tool.  The PS-2 model is designed for  a max speed of 450 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.   Mixers can be permanently installed if desired.

Made of 304 polished stainless steel, the HD model is designed for heavy duty jobs in 75-100 gal. (300-400 qt.) containers. It easily fits any 3/4″ electric chucked power tool.  The HD model is designed for a max speed of 250 RPMS.  Tools with 450-750 RPMS get the best rate of thorough mixing.  Mixers can be permanently installed if desired.